Predicting an answer
How to take a diagram and use it to make predictions
The environments above show what an ideal model predicts. These guides show how to build that prediction yourself: choose an object or system, draw its interactions (as we have done above), choose positive directions, and use a physical law to calculate a prediction. Sadly, we do not get the payoff of seeing how those predictions match or observations in the real world with a high degree of precision, so that is for yourself to try out!
Use meters, kilograms, and seconds throughout, with . Force is measured in newtons, energy in joules, and momentum in . A subscript (like e.g. ) means the initial value. A negative component means “opposite my positive axis” (whatever we choose that to be); speed is the nonnegative magnitude of velocity (think for a vector).
Cosine gives the component adjacent to the chosen angle; sine gives the opposite component. First identify which angle your diagram actually labels. Use degree mode for the setup angles shown in degrees. Angular equations of motion and small-angle approximations below use radians.
Before solving, name the unknown and check the assumptions. After solving, check the units, direction, and whether the size makes sense. The examples below use each environment’s reset setup, with rounding only at the end; changing a slider means substituting your new values into the same model.
Throughout, it is justifiably easy to get frightened from the large amount of formulas to memorize. However, the trick is not to memorize all the formulas. Eventually you will have seen them so many times that they will be memorized, but the trick is to think about why these formulas are what they are. With enough understanding and some good intuition, it should not be too hard to rederive the formulas from scratch. After all, someone (in our case, I believe, Galileo Galilei, Sir Isaac Newton, and Robert Hooke are to thank) had to derive these formulas first.
Ramp
Common questions: What is the acceleration? How fast will the block reach the bottom, and how long will it take? Here the block slides from rest down a fixed, frictionless slope; it does not roll.
1. Choose axes that make the constraint simple
Take positive downhill along the slope, starting at the release position, and positive perpendicular direction away from the surface. Draw two interactions on the block: its weight vertically down and the normal force perpendicular to the slope. The angle between weight and the direction into the ramp equals the ramp angle above horizontal. The downhill component is opposite that angle, so projecting the weight gives
The perpendicular acceleration is zero while the block remains on the surface. Newton’s second law along each axis therefore gives
The normal force balances the perpendicular component of weight, not the entire weight. Mass cancels from the acceleration because both force and inertia scale with it.
2. Connect acceleration to the requested quantity
Acceleration is just gravity, which is constant (with some simplified, yet reasonable assumptions). For a downhill distance and initial velocity ,
Solve for the positive travel time and downhill speed:
Reset example: , , . The downhill force is and the normal force is . Thus , , and .
3. Check with energy
For the block–Earth system, gravitational potential energy becomes kinetic energy. The fixed ramp’s normal force does no work because it is perpendicular to the motion. With vertical drop ,
This independently organizes the same model and gives the same speed. It does not give the travel time by itself. With friction, both the force balance and mechanical-energy calculation must include its effect, meaning these formulas no longer apply unchanged.
Projectile
Common questions: Where does it land? When does it reach its highest point? How high does it go? Treat the object as a particle with no air resistance and constant gravity.
1. Split the launch velocity
Put the origin at launch, with right and up positive. For initial speed at angle above horizontal,
Gravity is the only force during flight, since after the projectile is launched, the force exerted on it such that it began to move, no longer applies, so and . The horizontal and vertical equations use the same time:
Horizontal velocity stays constant. At the top only the vertical velocity is zero, so the object still moves horizontally and accelerates downward.
2. Use the condition that defines the event
For landing at launch height, set . One solution is , the launch itself. The later landing time and range are
For the highest point, set instead:
Reset example: and give and . Landing occurs at , from launch. The maximum height above launch is .
What if landing is at a different height?
The symmetric-flight shortcut no longer applies. Set the vertical displacement to the actual landing height relative to launch, , and solve
Select a positive root corresponding to the contact you mean, then substitute that time into . A target above launch can be crossed twice, once ascending and once descending, or never reached. The current environment models only a ground surface at launch height.
Pendulum
Common questions: How long is a cycle? How fast is the bob at the bottom? What does the string tension do? Assume a point bob, a massless string of fixed length , no drag, and release from rest at angle .
1. Resolve forces along and across the path
Measure from the downward vertical, positive toward the right-hand extreme. Along the circular path, gravity restores the bob toward the bottom:
Dots mean time derivatives: is angular velocity, angular acceleration, is angular jerk, is angular snap, etc. (See this Wikipedia page for the fun terms for higher derivatives of position!). Use radians in these equations. Inward along the string, tension and weight supply the acceleration that curves the motion:
“Centripetal force” names this inward resultant, not a third force to add to tension and gravity. At an extreme the speed is zero but tangential acceleration is not. At the bottom tangential acceleration is zero but inward acceleration is not.
2. Choose energy for speed, an oscillation model for time
The height above the bottom is . Conservation of mechanical energy for the bob–Earth system applies because there is no drag and string tension is perpendicular to the motion, so it does no work. This gives
For small angles, in radians (very painful, but approximations are ok to use in physics), making the equation of motion simple harmonic. Its period, the time back to the same extreme, is
Reset example: and give bottom speed and approximate period . The nonlinear equation used by the animation gives instead. That difference comes from the small-angle approximation, not rounding. The animation integrates the nonlinear equation numerically; larger release angles lengthen the period. Mass cancels from both speed and period in this ideal model.
Pendulum equation and period, inward force, and conservation of energy · OpenStax
Spring
Common questions: What are the force and speed at a position? How long is a cycle? Here a block moves horizontally without friction, attached to an ideal Hooke spring.
1. Turn the restoring force into an equation of motion
Choose at equilibrium and positive right. The spring constant has units . Its force and Newton’s second law are
The minus sign says the force points toward equilibrium. For release from rest at , define angular frequency . Then
is measured in radians per second; the trigonometric argument is in radians. These expressions satisfy both the force law and the initial conditions.
2. Use energy when time is unnecessary
For the block–spring system, gravitational and support forces do no work along the horizontal motion. Thus
This gives speed; choose the velocity’s sign from the direction of motion. Maximum speed occurs at :
Reset example: , , and give , , and . At release, and . At equilibrium, force and acceleration are momentarily zero while speed is greatest. Damping or a spring outside its Hooke-law range requires a different model.
Simple harmonic motion and its energy · OpenStax
Collision
Common questions: What are the velocities after impact? Do the carts stick or rebound? How much kinetic energy remains? Choose both carts as the system, with positive right, and assume negligible external horizontal impulse during the short collision. Write initial velocities as and final velocities as ; the environment has .
1. Write the equation that holds in both modes
The carts exert equal and opposite impulses on each other, so their total momentum is conserved:
This is one equation with two unknown final velocities. It needs another condition describing the collision. Momentum of each cart separately is not conserved.
2. Supply the collision condition
Sticking: the carts share one final velocity, :
Elastic: kinetic energy is also conserved:
For a one-dimensional elastic impact, combining this with momentum conservation gives : relative separation speed equals relative approach speed. With , solving the two equations gives
A negative final velocity means rebound to the left. Squaring velocities in kinetic energy removes their signs, while momentum still needs them.
3. Check momentum and account for energy
Reset example: , , . Initially, momentum is and kinetic energy is .
- Stick together: both move at . Total momentum stays , but kinetic energy becomes .
- Elastic: cart 1 stops and cart 2 moves at . Both total momentum and kinetic energy retain their initial values.
The lost kinetic energy in sticking becomes internal energy, such as deformation and heating; total energy is still conserved. These equations predict velocities across an ideal instantaneous impact. They do not determine contact force or contact duration.